Avue T Crown

Avue T Crown:

Fluorescent Temporary Crown & Bridge Material

Indications:

• Creating Short term/long term Temporary crowns or bridges
• Direct fabrication of temporary veneers, inlays, onlays
• Also used in indirect restorative procedures

Avue T Crown Automix (76gm):

• 1 x 76gm Automix
• Accessories

Avue T Crown Smartmix (10ml):

• 1 x 10ml Smartmix
• Accessories

Avue T Crown Automix (50ml):

• 1 x 50ml Automix 
• Accessories

Avue T Crown

PRODUCT DESCRIPTION

Avue T Crown is a Self-curing composite for natural looking long and short term temporization. It is automatically mixed and available in the mixing ratio of 1:1.

INDICATIONS

• Creating Short term/long term Temporary crowns or bridges
• Direct fabrication of temporary veneers, inlays, onlays and also used in indirect restorative procedures

CAUTION

• For dental use only
• Keep out of reach of children

INTERACTIONS

Avoid prolonged or repeated contact with skin (allergic contact dermatitis), oral soft tissues, and eyes. Avoid prolonged inhalation. Do not take internally.

Before using this product wear protective glasses as well as covering the patient's eyes to protect from splashing material. In case of contact with eyes, rinse immediately with plenty of water and seek medical attention. If contact with skin occurs immediately wipe off thoroughly with cotton and alcohol and then wash well with soap and water. If skin rash and sensitivity or other allergic reaction occurs discontinue use and seek medical attention.

Avoid contact with oral soft tissues. If accidental contact occurs, flush mucosa with plenty of water and expectorate water.

Do not use with any eugenol containing material.

DIRECTION OF USE -CARTRIDGE USING DISPENSOR{1:1} Recommended use

1. Before preparing the crown or bridge or prior to extraction of a tooth, take an impression using alginate, silicone or a thermoplastic impression material. Alternatively, the temporary prosthesis can be made using a laboratory prepared vacuum-formed tray.
2. Dry the prepared teeth and even out any undercuts in the preparation. Then lightly lubricate the cores and surrounding tissue plus any composite core build-ups using petroleum jelly or a similar separating medium.
3. Select the desired shade of Avue T Crown and insert the appropriate cartridge in the Automix-Dispenser.
4. Slide up the lever present on the back side of the dispenser & simultaneously pullback the plunger.
5. Lift up the plastic flap (Cartridge Lock) present on the front side.
6. Now load the cartridge, ensuring that V-shaped notch of the cartridge is facing downwards.
7. Push down the plastic flap and lock the cartridge.
8. Remove the cartridge cap by rotating its 90 degree anticlockwise and discard it.
9. Attach mixing tip and turn it clockwise to lock it.
10. Before applying the tip, check that the two cartridge openings are not clogged, and bleed the cartridge until the base and catalyst paste are evenly extruded .
11. By pulling the trigger material is mixed while using it for the first time squeeze out a pea sized amount of material and discard it.
12. Without delay, begin dispensing Avue T Crown Material directly into the preliminary impression into the area of the preparation by applying continuous, light pressure . As the material comes out of the mixing tip, inject it into the deepest portion of the preliminary impression and then into the gingival areas.

NOTE : Always keep the mixing tip immersed in the material to prevent bubbles.

1. After application of Avue T Crown leave the used mixing tip on the cartridge to cap the unused material.
2. Reseat the preliminary impression into the patient's mouth in the proper relative position within 50 seconds of the start of mix.

NOTE : The use of lubricant may assist in removal from the mouth.

1. After 1 -2min remove the impression from the mouth. Material hardened but still is in elastic state (model setting time is 3-4 minutes).
2. After removing from mouth, Let it set outside the mouth for 4 minutes. Temporary crowns can be immersed in warm water ( 45° -55°C) for post curing.
3. 5 minutes from the beginning of application, the temporary crown & bridges can be finished and polished.

NOTE : Prior to this remove air-inhibited layer with alcohol saturated gauze.

Cementing of Temporary Prosthesis.

Preferably cemented with Eugenol free Luting cement.

REPAIRS

Avue T Crown show high mechanical strength. However if temporary breaks , The both ends of the fracture segment are cleaned, roughened and provided with some mechanical Retention. Afterwards fixed with freshly extruded material.

Alternatively, the temporary prosthesis can also be repaired using the light-cure flowable composite.

CLEANING AND DISINFECTION

The auto mix dispenser is reusable after disinfection. Disinfection can be carried out with a suitable commercial Dental disinfectant solution.

STORAGE AND SHELF LIFE

1.            Store impression at room temperature (25 - 27 °C) in a dry place away from light.

2.            After the application, leave the used tip on the cartridge to cap the unused material.

3.            Do not use the material after the expiry date.

TECHNICAL DATA