SDI Conseal F

SDI Conseal F

SDI Conseal F

600 630

Manufacturer: SDI

Buy Now

Deal of the Month

INDICATIONS: 1.

Sealing of teeth with sound but vulnerable pit and fissure sites.

2. Sealing of teeth with minimal pit and fissure caries.

CONTRA-INDICATIONS:

1. Do not apply over carious areas.

2. Do not apply to unetched areas.

3. Product may cause skin irritations to some people. In such cases, discontinue use and seek medical attention.

PRINCIPLE COMPONENT: Multifunctional methacrylic ester.

APPEARANCE: A low viscosity resin which changes to a solid mass after light curing.

SDI Conseal F Pit & Fissure Sealant

Conseal f is fluoride releasing and combines clinically proven SDI sealant technology with an intensive initial fluoride boost in conjunction with long term fluoride treatment. The unique Conseal f filler component, with its blend of particles and high surface-to-area volume ratios maximizes the sealant’s fluoride release.

INDICATIONS:

1. Sealing of teeth with sound but vulnerable pit and fissure sites

2. Sealing of teeth with minimal pit and fissure caries

CONTRA-INDICATIONS:

1. Do not apply over carious areas

2. Do not apply to unetched areas

3. Product may cause skin irritations to some people. In such cases, discontinue use and seek medical attention.

Features :-

  • 1 x 1g syringe

Conseal f and Conseal are the lowest viscosity sealants with the greatest flowability. Their optimal flow characteristics achieve superior homogeneous penetration. The lower shrinkage of SDI’s unique resin system results in a tighter seal that optimizes the mechanical retention. Conseal f is fluoride releasing and combines clinically proven SDI sealant technology with an intensive initial fluoride boost in conjunction with long term fluoride treatment. The unique Conseal f filler component, with its blend of particles and high surface-to-area volume ratios maximizes the sealant’s fluoride release.

INSTRUCTIONS FOR USE:

1. Clean the occlusal surface of teeth with sound but vulnerable pit and fissure sites by using a nonfluoridated, oil-free prophylaxis paste. Remove minimal pit and fissure caries with small round burs in a slow speed handpiece. Do not extend into the sound portion of the fissure system. Rinse thoroughly with water. Isolate tooth.

2. Dry the surface to be etched with clean, dry, oil-free air.

3. Etch occlusal surface with 37% phosphoric acid such as Super Etch or Super Etch Low Viscosity (LV), (SDI Limited) for at least 30 seconds but no more than 60 seconds. IMPORTANT: If using an etch syringe, ensure that the dispensing tip hub is firmly attached to the syringe by twisting the hub securely onto the syringe. On first usage or after prolonged storage, extrude a small amount onto a mixing pad for familiarity with the material viscosity and rate of extrusion. 4. Wash thoroughly with water.

5. Completely dry tooth with clean, dry oil-free air for 15 seconds. IMPORTANT: A dry etched enamel surface should have a matt white appearance. If this is not so or the area has become contaminated with saliva or blood, repeat steps 2-5.

6. Apply sealant. IMPORTANT: If using the syringe system, ensure that the dispensing tip hub is firmly attached to the syringe by twisting the hub securely onto the syringe. On first usage or after prolonged storage, extrude a small amount onto a mixing pad for familiarity with the material viscosity and rate of extrusion. Place the tip against the surface to be coated and slowly extrude the sealant. Note: After each use, slightly pull back the syringe plunger to prevent dripping.

7. Light cure sealant for 20 seconds using SDI’s Radii Plus LED Curing Light or any other visible light curing device (440 - 480 nm wavelength). Further increments may be added provided proper isolation and dryness are maintained. Wipe off the oxygen inhibited layer and ensure no voids.

Related Products

Latest Blogs